Nipros HDM-70WV Instrukcja Użytkownika

Operating Instructions取 扱 説 明 書Before operating the system, please read this manual thoroughly and remain it for future reference.HDM-70WV/SVolume1, 1

Names and Functions of Parts10リアパネルRear panelRear TALLY Indicator (RED only)Lights up to RED when the tally signal is input to the TALLY IN 1 or TALLY

Names and Functions of Parts11リアパネルRear panelSDI(HD/SD) IN 1 connector (BNC)SDI(HD/SD) RET IN (SDI return signal input) connector (BNC)SDI(HD/SD) 1 OU

Names and Functions of Parts12リアパネルRear panelFanWorks when the POWER switch is turned on.電源スイッチを ON すると、ファンが回転します。DC IN connector(XLR 4-pin)POWER swit

Names and Functions of Parts13左側面. 右側面 および 上面, 底面Left side, Right side, Upper & BottomScrew holes (2-w1/4(left, right)) Used to fix the supplied ti

HDM-70WV 組み立て方法Fixing 組み立て方法14アームの取り付け方法VF Tilt Arm Stay FixingMake sure to disconnect the connectors before fixing up. 1Prepare the supplied VF Tilt

15Fixingアームの取り付け方法3Insert the VF Arm Stay into the gap between the combination washer and the screw, and tighten the armstay screw with the rubber was

16Fixingスイングアームへの取り付け方法 Mounting on Swing Arm ( for HDM-70WV/S only )Make sure to disconnect the connectors before fixing up. 12組み立ては、必ず入出力コネクタの配線をはずして

17Fixingスイングアームへの取り付け方法Mount a camcorder on the tripod base on the swing arm.4スイングアーム上の三脚ベースへカメラを取り付けます。 Mounting on Swing Arm ( for HDM-70WV/S only )

18ロケ用スタンドの脱着方法 Location Stand Removal and Fixing1Loosen/tighten four screws on the bottom to remove/fix. 本体の底面の4本のネジで行います。FixingLocation Stand(supplied

19Fixingフードの取り付け方法 Hood Mounting ( for HDM-70WV/S only )HD Monitor HDM-70WV/S1Prepare the supplied Hood and four screws.フードと固定ネジ4本を用意します。Tighten four

WARNINGFor the customers in the U.S.A.This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Par

HDM-70WV 接続方法Connection 接続方法20電源の接続方法Power Supply ConnectionMake sure to turn off the POWER switch of each unit before connecting. 接続する前には、必ず各機器の電源スイ

Connection21HD/SD-SDIビデオ信号の接続HD/SD-SDI video signal connection1Connect the HD/SD-SDI output signal from a camcorder to the SDI (HD/SD) IN 1 connector.

Connection22HD/SDアナログコンポーネント信号の接続HD/SD Analog Component Video Signal Connection1Connect the HD/SD analog component video output signal from a camcorde

Connection23音声信号の接続Audio Signal ConnectionMonitor speaker1Connect the AUDIO OUT 1/2 connectors ( XLR 3-pin ) to a mixer, etc. with a XLR 3-pin cable.

24タリー信号の接続TALLY Signal ConnectionConnectionThe Front TALLY indicator lights up when the tally input signals are as follows. 12Connect the tally output

Connection25ズームリモコンの接続Zoom Remote Controller (RETURN Controller) Connection1Connect the output signal from a zoom controller to the RET IN ( zoom remo

Adjustments and Settings 調整・設定26ビデオ信号の設定・調整Video Signal Setting and Adjustment USER preset functions, etc. work when the video signal is input. 注意 :

27ビデオ信号の設定・調整Video Signal Setting and AdjustmentAdjustments and Settings3明るさ/コントラスト/シャープネスの調整INFO ［1080i/60］PICTUREMARKER ・ ・SETUPRE

28ユーティリティー機能 - ユーザー設定UTILITY Function - User SettingPress the MENU button,and the menu list is displayedon the screen.PressMenu DisplayBy rotating th

29ZEBRA buttonMARKER buttonOFF(no marker)16:916:9 with +4:34:3 with +all markers4:3/16:9CROSS HATCH (LARGE)OFFON←←←←←←←←←←USER setting←Adjustments

各部名称と働きNames and Functions of Parts組み立て方法Fixing414HDM-70WV 目次Contents 目次HD Monitor HDM-70WVFront panel 4Rear panel 10Left side, Right side,Upper and

30HD Monitor HDM-70WVAdjustments and Settingsユーザー設定User Function Setting6-3UTILITYOn the MENU, adjust and set the USER settingof the AUDIO, WAVEFORM a

31HD Monitor HDM-70WVAdjustments and Settingsユーザー設定User Function SettingWAVEFORMVECTORSCOPEWAVEFORMAUDIO LEVEL METER100 80 60 40 20 0¦¦¦¦¦¦¦¦

32HDM-70WV 調整・設定ユーザー設定User Function SettingAUDIO ［ON］オーディオMenu of the AUDIO for the UTILITY/USER settingsON8OVERLAP 15- 20dB- 6dB12ON or

33Adjustments and Settingsユーザー設定User Function SettingMenu of the WAVEFORM for the UTILITY settingsVECTORSCOPE ［ON］WAVEFORM ［ON］RETURNWAVEFORM

34オーディオの設定・調整AUDIO Signal Setting1INFO ［1080i/60］PICTUREMARKER ［ON］AUDIO ［ON］WAVE FORM

35音声信号の設定Audio Signal Setting3By pressing the VOLUME / PUSH SELECT knob-button select the monitor audio signal by the monitor speakeror the headphone

36タリー信号の設定TALLY Signal SettingAdjustments and SettingsHD Monitor HDM-70WV1Make sure that the front and rear TALLY indicators, RED and GREEN, light up

37Adjustments and Settings補足AdditionHD Monitor HDM-70WVRETURNTIMECODE DISP ［OFF］TIMECODE TYPE ［LTC］TC TALLY ［OFF］LOW

38Accessories 付属品HDM-70WV＜Contents＞HDM-70WV main componentLocation standUniversal headVF tilt arm stayBNC cable(1.0 m)Power tap cable(1.2 m)AC adapt

39外形寸法図（単位：ミリ）Outside dimension (unit: mm)Outside View & Dimensions 外形寸法図HDM-70WV 外形寸法図19532.2 147189.535.846.4162-1/4-20 UNC(TOP, BOTTOM)3/8-16

HDM-70WV 各部名称と働きNames and Functions of Parts 各部名称と働き04フロントパネルFront panelScreen (with Bezel and Protector)Front TALLY Indicator LED (RED and GREEN)Lig

40Specifications 仕様HDM-70WV 仕様HD Monitor HDM-70WVPanel size 7.0 inches diagonalPicture Resolution800(H) x 480(V) x 3(RGB). Effective PixelsInputDC IN

H D M - 7 0 W V H D M - 7 0 W V / SOperating Instructions

Names and Functions of Parts05フロントパネルFront panelVOLUME / PUSH SELECT switchINPUT select switchZEBRA indication on/off switchMARKER size select switchBy

Names and Functions of Parts06フロントパネルFront panelMENU button / ENTER knob-buttonMENU button : Pressing the MENU button displays the MENU on the screen.

Names and Functions of Parts07フロントパネルFront panelBRIGHT level control volume and select switch / LED IndicatorCONTRAST control volume and select switch

Names and Functions of Parts08Operating the Menus メニューの操作PressRotateMenu Displayメニューの表示 Press the MENU button. The menu list is displaye

Names and Functions of Parts09VECTORSCOPE ［ON］ZEBRA ［OFF］SETUPRETURNTIMECODE DISP ［OFF］TIMECODE TYPE ［LTC］TC TAL